This is a blog about high loop kits and how to properly use them for a quiet dishwasher.
A high loop kit is an easy to install kit that will eliminate noise from your dishwasher. It is called a high loop because it creates a loop in the drain hose that is above the water level of your sink. This can be done by using the countertop or hanging the hose from the underside of your cabinet.
This type of installation is needed when you have garbage disposal connected to your dishwasher. The reason for this is because without installation, the pump in your dishwasher cannot properly drain all the water through the disposal and this results in water being splashed back up into your sink causing noise as well as other problems such as mold.
The way it works is if you don’t have an air gap installed on your sink, then you need to install a high loop kit. The kit includes everything needed to create an air gap in order to allow for proper drainage from your dishwasher without splashing water back into your sink.
There are different types of kits available depending on what type of faucet or kitchen sink setup you have in place (single hole, double hole). If you’re unsure about which type would work best for you then just call
High loop kits are used to raise the drain connection of a dishwasher and reduce the amount of noise that is created by the dishwasher. This kit is designed for a quiet dishwasher system under the counter. There are several types of high loop kits that you can use to make sure that your dishwasher is providing you with a quiet performance in your home.
High loop kits are available in different sizes and shapes depending on the type of connection that you have on your pipes. The most common types are known as straight, right angle, and off set elbow models. These all have different ways to connect to your current drain pipe. You may need to measure your drain pipe in order to determine which one is going to fit best for you.
If you feel like you may have to cut a hole in the wall in order to get your dishwasher drain pipe connected, then you may want to consider getting an adapter kit that will work without having to do this. Make sure that it fits before making any cuts or installing anything though so that you do not damage anything in your home.
Installing A High Loop Kit:
You will first need to turn off your water supply before starting this task. You can do this by turning the handle on the valve clockwise until
Reduce Noise from Your Dishwasher with a High Loop Kit
A high loop is a common plumbing installation technique in dishwashers that is used to prevent backflow of sewage into the dishwasher. Sewage and dishwater are two different systems and should remain separated. A high loop ensures that whatever is being discharged from your dishwasher does not flow back into the clean water system. The high loop also reduces noise from your dishwasher by having air flowing in a circular motion as opposed to having water flowing through it. By having air flowing through the pipe, you will hear less vibration and noise coming from your dishwasher.
How to use a high loop kit:
Turn off the water supply lines leading to your dishwasher and turn on the faucet to relieve pressure in the lines.
Pull out your dishwasher – there may be an access panel underneath or behind it that you can remove in order to reach the water supply lines. This will also give you more room to work when installing the high loop kit.
Disconnect the water supply line from the faucet leading to the dishwasher (or disconnect both supply lines if necessary). The existing small diameter hose should be connected to a 3/8″ compression fitting, then you will connect this new 1
There is a solution to this problem. It’s called a high loop. A high loop is a section of hose that runs from the dishwasher drain up to the underside of the countertop. This allows the flow of water to be higher than the drain itself. The result? Water flow noise is prevented and you’ll enjoy a quiet kitchen once again.
How To Install A High Loop Kit
The first step in installing your high loop kit is to measure and cut your hose. You should leave about an inch of extra hose just in case you need it for future repairs or replacements.
Next, install your piece of tubing onto the drain connector on your dishwasher by sliding it over the tube until it’s snugly in place. With your tubing installed, you are ready to connect it to your main water line with a T-fitting or Y-fitting (depending on whether or not you already have a water line running down your cabinet wall).
Once connected, run your dishwasher with no dishes inside and observe any leaks. If there are no leaks, you have successfully installed a high loop kit!
If you have a noisy dishwasher, it may be time to install a high loop kit. A high loop kit is a device that helps reduce the amount of noise produced by your dishwasher when it drains. The kit features an air gap at the end of the drain hose that prevents water from backing up into the drain hose. In addition to reducing noise, it also prevents unpleasant odors and contamination of clean water with dirty water.
A high loop kit can be used as a preventative measure if you have not had problems with your dishwasher yet, but fear you might have these problems in the future. However, they are more commonly found in older homes and apartments where the dishwashers are still working but are starting to make too much noise.
A high loop kit is not a product you will find in many home improvement stores. It is a device that has been designed to reduce noise from your dishwasher. The dishwasher high loop is designed to ensure the proper drainage of your dishwasher and reduce the amount of water that is left sitting in the bottom of your dishwasher.
Why do I need to install a Dishwasher High Loop Kit?
A Dishwasher High Loop kit is necessary when your sink drain line is lower than the level of the drain hose on your dishwasher. When this situation occurs, the drain hose can not properly drain all of the water from the dishwasher and it leads to standing water in the bottom of your dishwasher or even worse, it can cause dirty water to be splashed back on to your dishes during a wash cycle. A high loop kit is actually an extension that allows for proper drainage and reduces the chance for this problem to occur.
How to Install a Dishwasher High Loop Kit
Installing a high loop kit is fairly simple and can be done by nearly anyone who has basic handyman skills. The dishwasher high loop kit essentially adds an extension on top of your existing drain line. This extension stops dirty water from being splashed back up on to clean dishes during
Most dishwashers sold today come from the factory with a high loop. This is a section of drain hose that is looped up near the dishwasher’s top and secured in place with a cable tie. It’s not just for looks, it’s functional. The high loop prevents water from siphoning back into the dishwasher if power is lost during the wash cycle.
For those of you who do not have a high loop already installed on your dishwasher, luckily there is an easy way to retrofit one. All it takes is a little bit of plumbing know-how and about 5 minutes of your time. In this article we will cover what you need to know to install your own high loop kit using common household tools and materials.
What You Will Need